Menu Close

How do I find HBA details in Linux?

How do I find HBA details in Linux?

Re: HOW TO FIND HBA DETAILS IN LINUX You probably will find your HBA module in /etc/modprobe. conf. There you can identify with “modinfo” if the module is for QLOGIC or EMULEX. Then use SanSurfer (qlogic) or HBA Anywhere (emulex) to obtain detailed and accurate information.

How can I check my HBA status?

Instructions

  1. #lspci -vvv | grep -I HBA. We can see following entries in the output 03:00.1 Fibre Channel: QLogic Corp. ISP2432-based 4Gb Fibre Channel to PCI Express HBA (rev 03)
  2. #systool -v. Or. To check WWNN , run the following command.
  3. #cat /sys/class/fc_host/hostN/node_name. To check port state, run.

What is WWN in Linux?

A World Wide Name (WWN) or World Wide Identifier (WWID) is a unique identifier used in storage technologies including Fibre Channel, Parallel ATA, Serial ATA, NVM Express, SCSI and Serial Attached SCSI (SAS).

What is HBA WWN?

The term host bus adapter (HBA) is often used to refer to a Fibre Channel interface card. Each Fibre Channel HBA has a unique World Wide Name (WWN), which is similar to an Ethernet MAC address in that it uses an OUI assigned by the IEEE.

How do I find my WWN number ESXi?

2. How to find HBA WWN via ESXi Shell / CLI:

  1. Connect to ESXi shell either via putty/SSH or DCUI (Direct Console User Interface) / server console.
  2. Run ‘ls /proc/scsi/’ and check the folder names:
  3. Look for a folder like ‘qla2xxx’ – QLogic HBA, ‘lpfc820’ – Emulex HBA, ‘bnx2i” – Brocade HBA;
  4. Run ‘ls /proc/scsi/qla2xxx’.

How do I enable HBA on Linux?

How to disable or enable an HBA without reboot under CentOS/RHEL

  1. Locate the HBA address on the PCI bus: # lspci -k …
  2. Disconnect the PCI device from the PCI bus using the device driver name and the PCIbus address found earlier:
  3. Attach the device to the driver:

What is HBA in Linux?

Fibre Channel (FC) Host Bus Adapters(HBA) are interface cards that connects the host system to a fibre channel network or devices. The two major manufacturers of FC HBAs are QLogic and Emulex and the drivers for many HBAs are distributed in-box with the Operating Systems.

How do I find my HBA driver version in Linux?

Check HBA card and its driver’s info in linux(RHEL6)

  1. To check if the host has HBA card installed and which type of card installed, physiical slot, driver, module information. # lspci | grep -i fibre.
  2. check if the driver/module loaded in kernel.
  3. check author,description,mdule file name, license, driver version.

Where is the WWN number on a Linux virtual machine?

Here is a solution to find WWN number of HBA and scan the FC Luns.

  1. Identify the number of HBA adapters. systool -c fc_host -v.
  2. To get the WWNN (World Wide Node Number) of HBA or FC card in Linux. cat /sys/class/fc_host/host0/node_name.
  3. [ads-post]
  4. Scan the newly added or rescan the existing LUNs in Linux.

Where is HBA WWN number ESXi server?

How to find FC HBA WWN in Linux?

There are several ways to find out FC HBA WWN in Linux/Unix operating systems. How To Find WWN in Linux Check HBA Connectivity Status. We can use lspci command to find the FC HBA adapter details first. lspci is a utility for displaying information about PCI buses in the system and devices connected to them.

How to check if HBA is installed in Linux?

If HBA is installed then we can see it’s details as shown above. check how many hosts (Ports/Cards) are there in your Linux machine using below command # ls /sys/class/fc_host host3 Using below command find if FC HBA is Online or Offline Or Link Status.

How to find the WWN number of the HBA card?

Run the below command for each host to see the WWN number of the HBA Go to /sys/class/scsi_host directory and run the below command to see the WWN number of all the HBA cards connected the server. Run the below command to find all HBA cards installed on the server

How to find WWN number in Linux?

How to Find WWN in Linux 1 First Method. If it is not available it can be installed on servers where HBA is already installed which will be really helpful in how to find WWN number information 2 Second Method 3 Third Method. If EMC Storage is being used so there is a chance you must have SYMCLI software installed. 4 Fourth Method.

Posted in Interesting